端子拉力測試標準(國標

《端子拉力測試標準(國標》由會員上傳分享，免費在線閱讀，更多相關內容在應用文檔-天天文庫。

1、端子拉力測試標準(國標)??端子與電線連接應牢固，在規定的拉力下不應損傷和脫開，其拉力值應不小于表2的規定。表2拉力值導體截面積,mm2?拉力,N??0.50?50?0.75?80?1.00?100?1.50?150?2.50?200?4.00?270?6.00?450?10.00?500?16.00?1500?25.00?1900?35.00?2200?≥50.00～120.00?2700?采用刺破連接方法時應符合下列要求：1.電線端面應平整，并與電線的軸線相垂直。端面處導體與絕緣層應在同一平面上。在連接處

2、電線應不彎曲，并在圖3所示a區內可見電線端部。2.端子與電線連接應牢固，在規定的拉力下不應損傷和脫開。0.35mm2電線拉力值應不小于50N。?什么是AWG？AWG是AmericanWireGauge的簡稱，單線導體是根據直徑、絞線是根據橫截面積來決定線號。CANARE公司使用的導體線號如下表所示。另外，線號越大說明導體的橫截面積越小。AWG??????????????導體橫截面積(mm2)13?????????????????????????2.8114?????????????????????????2.

3、1815?????????????????????????1.7516?????????????????????????1.2718?????????????????????????1.0020??????????????????????0.51,0.5622??????????????????0.34,0.37,0.3923??????????????????0.29,0.30,0.3124??????????????????0.20,0.22,0.2325?????????????????????????

4、0.1826??????????????????????0.14,0.1528??????????????????????0.08,0.0931?????????????????????????0.04雙絞線???100歐姆屏蔽電纜???????5類4對24AWG100歐???????5類4對26AWG屏蔽軟線???100歐姆非屏蔽電纜???????6類4對23AWG的UTP或SCTP???????超5類4對24AWG非屏蔽電纜???????5類????????????4對24AWG????????????4

5、對24AWG非屏蔽軟線????????????25對24AWG非屏蔽軟線???????4類????????????4對24AWG非屏蔽線????????????25對24AWG非屏蔽線???????3類????????????4對24AWG非屏蔽線????????????25對24AWG非屏蔽線???雙體電纜???????24AWG非屏蔽4/4對???????24AWG非屏蔽/屏蔽4/4對???????24/22AWG非屏蔽/屏蔽4/2對???????24AWG非屏蔽2/2對???150歐姆屏蔽電纜?????

6、??1A型???????6A型???????9A型