資源描述：
《TBT 3019-2001 變牙型防松螺母.pdf》由會員上傳分享，免費在線閱讀，更多相關內容在行業資料-天天文庫。
1、TB中華人民共和國t失越氫才于業摘?jiǎng)蛹裈B/T3019-2001變牙型防松螺母2001-05-28發布2001-12-01實施中華人民共和國鐵道部發布標準分享網www.bzfxw.com免費下載TB/*r3019-2001目次1范圍·············，·····················································································??12引用標準································，···········
2、·······································，·········??13定義，····················、·····················，·······················································??14型式與尺寸····················································，························?！ぁぁぁぁぁぁぁぁぁぁぁぁぁひ?5要求·······
3、··············，·············································································??26檢驗···································································································??37標記·...............................................................
4、.........................................38標志、包裝、運輸、貯存··········，·····，·······················································??3附錄A(提示的附錄)防松螺母螺紋牙型示例··························，··················??4附錄B(提示的附錄)防松螺母安裝要求·····，··············································
5、一5附錄C(提示的附錄)與防松螺母相配合的外螺紋·······················，··················??6TBA3019-2001前言本標準非等效采用美國MIL-N85353/11-1986nut(fastener),internalythreaded,hexagon,reducedheight.125KSIand200KSIFTU4500F(內螺紋、六角、減高度螺母，125KSI到200KSIFTU4500F)，其螺紋公稱直徑(D)符合國家標準GB/I'196-1981普通螺紋基本尺寸(直徑1-
6、600)中第一和第二系列。本標準的附錄A、附錄B、附錄C都是提示的附錄。本標準由上海鐵道大學提出。本標準由鐵道部標準計量研究所歸口。本標準起草單位:上海鐵道大學、鐵道部標準計量研究所、中國鐵路工程總公司電氣化工程局、鐵道部專業設計院、江蘇吳江天龍電氣化設備廠。本標準主要起草人:羅雁云、劉學峰、王作祥、曹亦清、胡金培。本標準2001年5月首次發布。標準分享網www.bzfxw.com免費下載中華人民共和國鐵道行業標準TB/'f3019-2001變牙型防松螺母1范圍本標準規定了螺紋公稱直徑為6mm-42二的變牙型防松螺母(以下簡稱防
7、松螺母)的定義、型式、尺寸、要求、檢驗規則和標志。本標準適用于有防松和重復使用性能的螺母。2引用標準下列標準所包含的條文，通過在本標準中引用而構成為本標準的條文。本標準出版時，所示版本均為有效。所有標準都會被修訂，使用本標準的各方應探討使用下列標準最新版本的可能性。GB/1'90-1985緊固件驗收檢查、標志與包裝GB/'r196-1981普通螺紋基本尺寸(直徑1-600mm)GB/1'197-1981普通螺紋公差與配合(直徑1-355rnm)GB/1'1237-2000緊固件的標記方法GB/1'3098.2-2000緊固件機械
8、性能螺母GB/1'3098.6-2000緊固件機械性能不銹鋼螺栓、螺釘、螺柱和螺母GB/'r3103.1-1982緊固件公差螺栓、螺釘和螺母GB/T5267-1985螺紋緊固件電鍍層GB/1'5779.2-2000緊固件表面缺陷螺母一般要求GB/1'6170-2
