資源描述：
《TBT3106-2005 鐵道車輛單制動缸高清》由會員上傳分享，免費在線閱讀，更多相關內容在行業資料-天天文庫。
1、ICS45.060.01s32TB中華人民共和國鐵道行業標準TB/T3106-2005鐵道車輛單元制動缸Brakecylinderunitforrailwaycar2005-03-29發布2005-07-01實施中華人民共和菌全失道部A*FTB/T3106-2006目次前言····?！ぁ?，··········································，······················，······························??I，勝范圍·、·、···、·······
2、·、···、·、、····，·，········、、、、、····。··，··、·、········，··、、、，·、··、······，、·、·、·??1，一規范性引用文件···························································································??1門j分類·.............................................................................
3、.................................1‘4技術要求······································································································??1氣︶試驗方法········，········，······················································································??26檢驗規則
4、········································································································，··?3︻1標志、包裝、貯存及運輸···············································································，·······??4TB/T3106-2005月叨呂本標準由中國北車集團四方車輛研究所提出并歸口。本標準起草單位:中國北車
5、集團四方車輛研究所、鐵道科學研究院機車車輛研究所、南京廣道工貿有限公司。本標準主要起草人:王俊勇、張聽、呂換小、方克娟、張繼達。本標準為首次發布。TB/T3106-2005鐵道車輛單元制動缸，范圍本標準規定了鐵道車輛單元制動缸的技術要求，試驗方法，檢驗規則，標志、包裝、貯存及運輸?shù)?。本?biāo)準適用于鐵道車輛新造單元制動缸。2規范性引用文件下列文件中的條款通過本標準的引用而成為本標準的條款。凡是注日期的引用文件，其隨后所有的修改單(不包括勘誤的內容)或修訂版均不適用于本標準，然而，鼓勵根據本標準達成協議的各方研究是否可使用這些
6、文件的最新版本。凡是不注日期的引用文件，其最新版本適用于本標準。GB/T528-1998硫化橡膠或熱塑性橡膠拉伸應力應變性能的測定(eqvISO37:1994)GB/T529-1999硫化橡膠或熱塑性橡膠撕裂強度的測定(褲形、直角形和新月形試樣))(eqvISO34-1:1994)GB/T531-1999橡膠袖珍硬度計壓人硬度試驗方法(idtISO7619:1986)GB/T1184-19%形狀和位置公差未注公差值GB/T1682硫化橡膠低溫脆性的測定單試樣法GB/T1690硫化橡膠耐液體試驗方法GB/T1804-200
7、0一般公差未注公差的線性和角度尺寸的公差GB/T2100-2002一般用途耐蝕鋼鑄件GB/T2941-1991橡膠試樣環境調節和試驗的標準溫度、濕度及時間(eqvISO471:1983)GB/T3512-2001硫化橡膠或熱塑性橡膠熱空氣加速老化和耐熱試驗(eqvISO188:1998)GB/T6414-1999鑄件尺寸公差與機械加工余量GB/T11352-1989一般工程用鑄造碳鋼件TB/T66-1995機車車輛制動機彈簧技術條件分類單元制動缸按密封件的結構不同可分為膜板式單元制動缸和皮碗式單元制動缸。4技術要求4.1
8、一般要求4.1.1單元制動缸使用的環境溫度為:一50℃一50`Co4.1.2單元制動缸的最高工作壓力為500kPao4.1.3單元制動缸應按經規定程序批準的圖樣和本標準的規定制造。4.1.4同一規格、型號的單元制動缸各零部件應具有互換性。4.1.5鑄鋼件應符合GB/T2100-2002,GB/T11352-1989的
